Automation Components Inc (ACI)

11638 products

Automation Components Inc (ACI)

A/WPR2-300-20-LCD

A/WPR2-300-20'-LCD - Wet to Wet Differential Pressure Transducer w/ Remote Probes. The A/WPR2 Series Remote Wet to Wet Differential Pressure Sensor is designed to reduce installation time and to provide mounting flexibilit often eliminating the need for additional plumbing. They accurately measure wet media pressures in a variety of applications. Commonly used for monitoring pump these devices are also ideal for measuring pressure across filter heat exchangers and compressors. The A/WPR2's enclosure opens conveniently to allow it to be reconfigured between three additional ranges (see order grid) and outputs of 4 to 20 mA (default 0 to 5 VD or 0 to 10 VDC. The A/WPR2 Series can measure pressure ranges as low as 0 to 15 psi and as high as 0 to 300 psi. The A/WPR2 also features a push button auto zero function for remote calibration efficiency. Our Pressure Sensors or Transmitters are designed for HVAC Building Automation and light industrial systems. Typical applications include: chilled wate hot water system DP across heat exchange chiller pump control proof of pump flow statu proof of water flow in chiller water source heat pump DP control of pump VFD heating and cooling water system and chiller evaporators. The A/WPR2 Series is covered by ACI's Five (5) Year Limited Warranty. ACI offers the SYPHON SERIES to help protect pressure transmitters from damage where the operating temperature of the steam being monitored is higher than the maximum operating temperature of the pressure transducer. ACI offers the SNUBBER SERIES to help protect pressure gauges and transducers against pressure surges. The porous filter design is suitable for use in ai ga and fluid applications. New LCD Option Flexibiity of Output Remote Probe Sensor Push button auto zero functio Ne Selectable PSI Ranges (10 and 30)

Automation Components Inc (ACI)

A/WPR2-300-40

Automation Components Inc (ACI)

A/WPR2-300-40-LCD

Automation Components Inc (ACI)

A/WPR2-300-M10

Automation Components Inc (ACI)

A/WPR2-300-M10-LCD

Automation Components Inc (ACI)

A/WPR2-300-M20

Automation Components Inc (ACI)

A/WPR2-300-M20-LCD

Automation Components Inc (ACI)

A1K2WRSORJ4LCDCA09

A/1K-2W-RSO-RJ4-LCD-C-A09-C5

Automation Components Inc (ACI)

A20KD12-PB

A/20K-D-12"-PB - 20K Ohms @ 77 Deg F (25 Deg C) Thermistor The standard plastic duct mount configuration has a mounting flange for quick installation and a foam pad to dampen vibrations. The sensing element is double encapsulated to avoid sensor failures caused by moisture infiltration. ACI duct temperature sensors are designed for HVAC Building Automation and light industrial systems. Specific applications include: zone control air handling unit and temperature monitoring. Negative temperature coefficient Double encapsulated sensor Built in mounting flange Easy open/close latch sysetm (no screws)

Automation Components Inc (ACI)

AAR

AAR - The AAR is controlled by a single analog input signal with two potentiometers controlling each output relay. The two 10 amp output relays can be independently set to fixed or adjustable deadband. ?Fixed the relay will turn ?ON? at the level set by the Low pot and will turn ?OFF? at a fixed 3% of the input signal below the turn-on level. ?Adjustable? allows a flexible range of deadband adjustment using the High and Low potentiometer. The edge-connector feature allows signal and power connections to be extended to the next board. This allows the installer to wire the first unit then slide additional units together by plugging into a power and signal bus without the need to strip and terminate additional wires.  The AAR is covered by ACI's Two (2) Year Limited Warranty. Digital output expansio Level indicatio Alarms