Automation Components Inc (ACI)

11638 products

Automation Components Inc (ACI)

EPW2G VERSION #4

Automation Components Inc (ACI)

EPW2GFS

EPW2GFS - The EPW* converts a puls phase cu or digital PWM signal into a proportional pneumatic signal ranging from 0 to 20 psig. The pneumatic output is proportional to the signal inpu either direct or reverse acting. The EPW* has a manual override potentiometer to vary the pneumatic output and two LED one to indicate power and one for signal status. The EPW* offers four jumper selectable input timing ranges. Output pressure ranges are jumper shunt selectable for 0 to 1 0 to 15 and 0 to 20 psi and adjustable in all ranges. A 0-5 VDC feedback signal indicating the resultant branch line pressur is also provided. This signal varies linearly with the branch pressure range selected. EPW* is designed with electrical terminals on one end and pneumatic connections on the othe allowing for maximum convenience in wiring and tubing installation when panel mounted. Three basic configurations are available: The EPW is a constant bleed interface with branch exhaust response time determined by the bleed orifice size and pressure differentials. If power fails to the EP it will continue to bleed through the bleed orifice until branch pressure is zero psig. The EPW2 incorporates two valves (one controls exhaust) and does not bleed air at set point. Its branch exhaust flow and response time are not limited by an internal restrictor and are similar to its load rate. If power fails to the EPW branch line pressure remains constant if the branch line does not leak air. FAIL SAFE: The EPW2FS is a two valve fail safe model. Its 3-way branch exhaust valve allowsm exhaust of branch line air on a power failure All factory calibrated products are NIST traceable. Certificates of Compliance must be ordered with product. EU Commission Directive 2002/95/EC (RoHS) Compliant. Three way mixing valve control Pilot positioner control Compressor staging

Automation Components Inc (ACI)

EPW2GFS/E

PNEUMATIC TRANSDUCER

Automation Components Inc (ACI)

EPWG

Automation Components Inc (ACI)

EPWG VERSION #2

Automation Components Inc (ACI)

EPWG VERSION #4

Automation Components Inc (ACI)

ESENSE II FAI DISP

Automation Components Inc (ACI)

ESENSE-D

ESENSE-D - The ESENSE room and duct transmitters monitor the carbon dioxide (CO2) levels in industrial, school, and office type environments. The concentration of CO2 is a good indication of the overall indoor air quality. The ESENSE Series is based on a single beam non-dispersive infrared technology and is a cost-optimized solution for the climate control of buildings and other processes. In addition, ABC software eliminates the need for manual calibration. The ESENSE Series measures the CO2 concentration in the ambient air up to 2,000 ppm and converts the data into an analog output. This data can be used in conjunction with a Building Automation or Demand Control Ventilation System to decrease energy consumption while creating a healthier indoor climate. Units come with combined outputs of 0-5VDC and 4 to 20mA or 0-10VDC and 4 to 20mA. Carbon Dioxide sensors or transmitters for HVAC, Building Automation Systems, or ANSI/ASHRAE Standard 62.1-2004.  Typical applications include: schools, office buildings, auditoriums, gymnasiums, shopping malls, theatres, demand control ventilation, economizers.

Automation Components Inc (ACI)

ESENSE-D-LCD

ESENSE-D-LCD - The ESENSE room and duct transmitters monitor the carbon dioxide (CO2) levels in industrial, school, and office type environments. The concentration of CO2 is a good indication of the overall indoor air quality. The ESENSE Series is based on a single beam non-dispersive infrared technology and is a cost-optimized solution for the climate control of buildings and other processes. In addition, ABC software eliminates the need for manual calibration. The ESENSE Series measures the CO2 concentration in the ambient air up to 2,000 ppm and converts the data into an analog output. This data can be used in conjunction with a Building Automation or Demand Control Ventilation System to decrease energy consumption while creating a healthier indoor climate. Units come with combined outputs of 0-5VDC and 4 to 20mA or 0-10VDC and 4 to 20mA. Carbon Dioxide sensors or transmitters for HVAC, Building Automation Systems, or ANSI/ASHRAE Standard 62.1-2004.  Typical applications include: schools, office buildings, auditoriums, gymnasiums, shopping malls, theatres, demand control ventilation, economizers.

Automation Components Inc (ACI)

ESENSE-IP50

ESENSE-IP50 - The ESENSE room and duct transmitters monitor the carbon dioxide (CO2) levels in industrial, school, and office type environments. The concentration of CO2 is a good indication of the overall indoor air quality. The ESENSE Series is based on a single beam non-dispersive infrared technology and is a cost-optimized solution for the climate control of buildings and other processes. In addition, ABC software eliminates the need for manual calibration. The ESENSE Series measures the CO2 concentration in the ambient air up to 2,000 ppm and converts the data into an analog output. This data can be used in conjunction with a Building Automation or Demand Control Ventilation System to decrease energy consumption while creating a healthier indoor climate. Units come with combined outputs of 0-5VDC and 4 to 20mA or 0-10VDC and 4 to 20mA. Carbon Dioxide sensors or transmitters for HVAC, Building Automation Systems, or ANSI/ASHRAE Standard 62.1-2004.  Typical applications include: schools, office buildings, auditoriums, gymnasiums, shopping malls, theatres, demand control ventilation, economizers.